Once they are inserted and aligned, place the top portion of the retainer over the tabs, and thread in the 6 provided bolts. Then, place the 3 metal pieces on top of the retainer, pushing each tab through the respective slit in the housing. Make sure that the o-ring stays in place in the groove until it’s all the way seated. Push the adjustable short shifter with the lower retainer into the shifter housing.
#ADJUSTABLE E36 SHORT SHIFTER INSTALL#
Install the included o-ring into the the groove on the bottom of the lower retainer.Ĥe. Push the lower retainer onto the main shifter pivot of the CravenSpeed Adjustable Short Shifter, approaching from the bottom.Ĥd. Spread a small amount of the included grease into the ball feature of the lower retainer.Ĥc. If you are installing the Cravenspeed Shifter Retaining Clip Pro, carry on with the instructions from here.Ĥb. Skip to step 4f and proceed with reinstalling the center console. If you do not have the awesome, new CravenSpeed Shifter Retainer Clip Pro, simply reinstall the OEM retainer clip onto your new Adjustable Short Shifter and reinstall the assembly back into the shift housing as shown below. Install the CravenSpeed Adjustable Short ShifterĤa. Place the shifter housing back down over the newly installed CravenSpeed bushings and replace the four 10mm nuts. Note the orientation of the bushings from the images below.ģc. Pull the stock bushings out from under the housing and replace them with the CravenSpeed bushings. Remove the four 10mm nuts holding the shift housing into place.ģb. (it may help to have a extra set of hands here)ģa. Compress the three clips on the white shift retaining clip then pull your stock shifter up and out. If you think you can accomplish the install with it still attached, by all means leave it alone.Ģc. NOTE: It may not be necessary to remove the shifter cable from the reverse pivot. They should pop off without too much effort. Use your wits and don’t overdo it and break anything. Place a drift or flat-head screwdriver next to the pivot cup and give it a firm whack with a mallet. Disconnect the shifting cables from the bottom of your stock shifter. Take off the left-side, red bushing and the pivot assembly should just slip right off.Ģb. Don’t stress if you mangle this push ring because we’ve included a replacement if you need it. Gently pry around it with a flat head screwdriver until it’s free. Remove the push ring (washer with teeth) holding the reverse pivot assembly in place.
#ADJUSTABLE E36 SHORT SHIFTER PRO#
You are now ready to proceed to the next step of the CravenSpeed Adjustable Short Shifter and/or MINI Shifter Retaining Clip Pro installation.Ģa. Feed the parking brake boot back through it’s mounting hole while you’re pulling up the center console.ġi. Starting at the rear, pivot/pull the center console up and out of the car. Pull your parking brake up as far as it will go and pop loose the boot frame where it snaps into the center console.ġh. There is a single Torx screw on each side that will also need to be removed.ġg. Remove the Torx screw holding the rear of the center console. Slide and flip your seats forward to access them from the rear passenger compartment.ġf. Remove the Torx screw in the center of the rear cup holder and the two Torx screws on either side then lift out the rear section of the center console. Remove the two Torx screws (one on each side of the center console) that are now exposed from removing the kick panels.ġe.
Remove these screws and pop off both kick panels one on each side of the center console.ġd. Each kick panel has a Torx screw located up high about halfway to the foot well wall. Utilizing a Trim Panel Removal Tool, pop the lower ring loose and unplug the Sport-Mode connecting wire before lifting it completely away.ġc. With a firm grip, pull up sharply and your knob should pop right off.ġb.
0 kommentar(er)
